Skip to content
NookMallow
All inspiration

The practical guides · Rental upgrades

How to Measure and Hang Curtains to Make a Rental Room Feel Taller

Start at the rod, finish half an inch above the floor. Use this 48-inch window example to work out what to buy and where to hang it.

The same rental bedroom before the update, with the black rod just above the window trim and ivory curtains ending at the sill.
Before · The rod sits just above the trim and the curtains stop at the sill, leaving a wide band of bare wall beneath the window.
The same rental bedroom after the update, with the black rod closer to the ceiling and full-length ivory curtains framing the window on both sides.
After · The wider rod lets the panels sit beside the trim. Long folds carry your eye from just below the ceiling to the floor.

Stand in the doorway and look at where the curtains start and stop. When both edges sit close to the window, your eye reads the window as a small rectangle in the middle of the wall. A higher rod and a long hem give that same wall a taller-looking frame.

These AI styling illustrations show the same rental bedroom from the same viewpoint. The window, furniture, window light and fabric color stay in place. The changes are the rod position and the length of the curtains.

01 / Rental upgrades

Mark the rod high and wide

If your lease permits mounting hardware, try marking the bracket height with painter’s tape about 4–6 inches above the top of the trim. In a room with a larger gap, try it a little higher. Leave space for the bracket and any fabric that stands above the rod, then judge the height from the doorway.

Allow about 6–8 inches of usable rod past the outside trim on each side where wall space permits. The extra space lets open curtains sit mostly on the wall so more glass shows. Check for a side wall, closet door or handle that would get in the way. Measure usable rod between the ends that stop the fabric, excluding decorative finials.

02 / Rental upgrades

Measure the width across the rod

Measure from the outside of the left trim to the outside of the right trim. Add the extension on both sides to estimate the usable rod width. Then look for a combined flat panel width around 1.5 to 2 times that number for an everyday gathered look. Take the manufacturer’s fullness guidance into account, especially for pinch pleats or heavy fabric.

Check whether the listing shows the width of one panel or the total for the pack. A set with two 52-inch panels gives you 104 inches of flat fabric. On a 64-inch rod that’s about 1.6 times the rod width, leaving enough fabric for some folds when the curtains are closed.

03 / Rental upgrades

Measure the drop to the floor

Measure from where the top edge of the finished panel will sit to the finished floor. A rod pocket, grommets and clip rings put that edge at different heights, so check the hanging style before you settle on a bracket position. With uneven floors, measure both sides and use the shorter drop if you want both hems to clear the floor.

For a floor-skimming hem with a little cleaning clearance, subtract about half an inch. Here’s how that works for a 48-inch window measured outside the trim.

Measure the drop to the floor
MeasurementWorked example
Trim width48 in.
Usable rod width48 + 8 + 8 = 64 in.
Combined flat fabric width2 × 52 = 104 in. (about 1.6× fullness)
Panel length96½ in. from planned fabric top to floor − ½ in. clearance = 96 in.

Decide where you want the hem to land, then measure from the top of the fabric.

04 / Rental upgrades

Work with the hardware your rental allows

If you’re keeping an existing rod, start with its installed height and pick the panel length that gets the hem where you want it. An inside-frame tension rod can be useful when drilling is off limits. It keeps the curtains within the opening, so the higher and wider effect needs a suitable mounting point outside the trim. Match any no-drill hardware to the frame style and the real weight of both panels.

Choose a light-filtering weave if you want softer daylight. For a bedroom that needs to be darker, consider lined blackout panels and check where light can enter around the edges. If a radiator, heater or air vent sits below the window, check its required clearances and stop the fabric above it where needed.

Curtains and a rod to compare

Use your measurements to pick one set of panels. Card images are AI styling illustrations. Check current price and delivery on Amazon.

As an Amazon Associate I earn from qualifying purchases.

05 / A few useful answers

Before you make the next choice.

What curtain length should I buy, 84 or 96 inches?

Buy for the drop you can actually hang. If the finished panel top will be 96½ inches above the floor, a 96-inch panel leaves about half an inch of clearance. Use 84-inch panels if the top is closer to 84½ inches above the floor or if you want a shorter hem.

How wide should curtains be for a 48-inch window?

If the usable rod extends 8 inches past the trim on each side, it will span 64 inches. Two 52-inch panels give 104 inches of flat width, or about 1.6 times the rod width. Check the product’s fullness guidance if you prefer more pronounced folds.

How can I make curtains look taller without moving the rod?

Start by measuring a panel that runs from your existing rod to just above the floor. A continuous vertical fold can visually lengthen the wall even when the bracket holes stay where they are.

Further reading

For the sizing or lighting principles mentioned above:

Start with your room

Make the next choice yours.

Share your room photos, tell us what stays and set your furniture budget. Find real product options and use an AI preview to explore the direction.

Find furniture for your room Confirm dimensions, availability and delivery at the store. Shipping and tax are separate.